CZ Duty 4.0 F and 4.0 C: red dot compatibility

In short

Red dots with these footprints go straight on the CZ Duty slide. You need no adapter plate - the pins that come in the box with the pistol are enough:

Which red dot? On a full-size pistol like the CZ Duty 4.0 F, we see no problem with a larger red dot and a big window. On the compact CZ Duty 4.0 C, we would rather pick a smaller one, so the red dot stays in proportion to the pistol. That is why our picks for the F are red dots with the Trijicon RMR footprint, and for the C red dots with the Shield RMSc footprint. A large red dot still fits the C - the pins make that possible.

CZ Duty 4.0 F and CZ Duty 4.0 C with red dots

Footprints and pins for the CZ Duty

The slide of the CZ Duty has one cut for many footprints. What changes is the set of pins you put in. Find your footprint and you know which pins to use.

Footprint Pins from the box Screw thread in the slide Plate needed
Trijicon RMR footprint Set 1 6-32 UNC No
Shield RMSc footprint Set 3 + 2 pins B M4 No
Holosun K-series footprint Set 3 M4 No
Leupold DPP footprint Set 2 + 2 pins A M4 No
Holosun 509T footprint Set 4 + 1 pin B M4 Yes, 509T plate
Aimpoint Acro footprint (Acro P-2) Set 2 + 2 pins B M4 Yes, Acro P-2 plate

The screws always come with your red dot, not with the pistol. Not sure which footprint your red dot has? Check red dots by footprint.

Mounting a red dot on the CZ Duty, step by step

Here is the CZ Duty manual in short. All you need is a T20 Torx screwdriver and the pins from the box.

CZ Duty slide with pins for the Trijicon RMR footprint

Trijicon RMR footprint: pin set 1

CZ Duty slide with pins for the Shield RMSc footprint

Shield RMSc footprint: pin set 3 and two pins B

  1. Take off the cover. Undo the screws of the cover on the slide with the T20 Torx and lift the cover off.
  2. Pick your pins. Use the table above to find the pin set for your red dot.
  3. Put the pins in. The front pins have a flat base and slide into the groove. The round pins (A or B in the table) go into a hole.
  4. Check the screws. Put the screws through your red dot. If a screw sticks out more than 4 mm under the red dot, shorten it or use a shorter one. A screw that is too long can stop the pistol from working and will not hold the red dot well.
  5. Set the red dot on the pins. The screw holes in the red dot must line up with the holes in the slide.
  6. Tighten the screws. Follow the red dot maker's instructions. CZ recommends 2 to 2.8 Nm. You can add a thread locker such as Loctite 243.

CZ Duty 4.0 F: a larger red dot

The F has the full-size grip and plenty of room on top. Here a larger red dot with a big window makes sense - you find the dot faster. Our three picks are the red dots with the Trijicon RMR footprint that our customers order most.

Every RMR red dot in one place

Every red dot with the Trijicon RMR footprint fits your CZ Duty F with pin set 1. CZ Parts keeps them in one collection.

Shop RMR red dots

First choice for the F

1. Olight Osight C

Olight Osight C red dot
  • Aiming point: 3 MOA dot, 32 MOA circle, or both.
  • Battery: changes from the side, so the red dot stays on the slide and keeps its zero.
  • Window: large, so you find the dot fast.
  • On the Duty F: a good all-round red dot for training and matches.

Large window for matches

2. Holosun 507 Comp [green]

Holosun 507 Comp green red dot
  • Aiming point: 2 MOA dot with 8, 20 and 32 MOA circles in different combinations.
  • Window: large, 1.1 x 0.87 inch.
  • Body: 7075 aluminium.
  • Battery: CR1632, up to 50,000 hours. Shake Awake turns it on when you move the pistol.

Lower price, large window

3. Vector Optics Frenzy 1x22x26 MOS

Vector Optics Frenzy 1x22x26 MOS red dot
  • Aiming point: 3 MOA dot.
  • Window: 22 x 26 mm.
  • Weight: 30 g, aluminium body, IPX6 water resistance.
  • Battery saver: motion sensor, switches off after 2 minutes without movement.

CZ Duty 4.0 C: a smaller red dot

The C has the compact grip, so the whole pistol is smaller. A smaller, slimmer red dot matches its size better. Our three picks are the red dots with the Shield RMSc footprint that our customers order most.

CZ Duty 4.0 C with an RMSc footprint red dot

Small red dots for the CZ Duty C

Every red dot with the Shield RMSc footprint at CZ Parts fits the C with pin set 3.

Shop RMSc red dots

First choice for the C

1. Olight Osight SE [red]

Olight Osight SE red dot
  • Closed body: the LED is sealed inside, so rain and dirt stay out.
  • Aiming point: 2 MOA dot, 32 MOA circle, or both.
  • Battery: CR1620, changes from the side without removing the red dot.
  • On the Duty C: small, sealed and simple to use.
Vector Optics Frenzy-S 1x17x24 MIC red dot
  • Weight: 18.4 g, all-metal body.
  • Aiming point: 3 MOA dot.
  • Window: 17 x 24 mm.
  • Battery saver: motion sensor, CR2032 battery for up to 50,000 hours.

Long battery life

3. Sightmark Mini Shot A-Spec M3

Sightmark Mini Shot A-Spec M3 red dot
  • Battery: up to 100,000 hours.
  • Brightness: sets itself to the light around you.
  • Window: 20 x 16 mm.
  • Body: 6061-T6 aluminium, shockproof and water resistant.

More about footprints and plates on other CZ models is in our compatibility guide.

Got a CZ Duty and a red dot you are not sure about? Send us the model name and we will check the footprint for you.

Search by model